Updated: May 23, 2022 by Kris Jarrett

IKEA Hack: Fabric Covered Chest

First off, I want to give you all a huge thanks for the sweet comments on my guest room makeover. You sure know how to make a girl feel good 🙂 My favorite part of our new guest room is the DIY chest that sits to the right of the bed.

Would you believe that it started out looking like this?

It’s the TRYSIL chest from IKEA – it’s not a bad looking chest but it didn’t exactly fit with the style of my room so I decided to do an IKEA hack by covering the chest with fabric (a Target tablecloth actually!) and switching out the drawer pulls. I couldn’t be happier with how it turned out:

There was a lot of trial and error in getting to the final product, but now that I’ve figured out the best way to do it, I could whip up another chest in no time. I’ve put together a pretty detailed tutorial for any of you who are interested in giving it a go (post includes affiliate links – see my full disclosure statement {here}):

The first step is to choose your fabric. About any fabric should work as long as it’s not too thick. You might want to steer clear of anything with a design or linear pattern to prevent driving yourself crazy trying to pattern match or keep the lines of your fabric straight. I was originally planning on using burlap, but I changed my mind after spotting this Target Threshold tablecloth in neutral. The color and texture were perfect for my room and it cost only $16.99 for a 60″ x 104″, which translates to less than $6 per yard.

Next, you’ll want to get all of the pieces of the TRYSIL chest out of the box and read through the assembly instructions to figure out which piece is which. Put a small piece of painter’s tape on the side of each piece that will be on the inside once the chest is assembled. Write the name of the piece (side, top, drawer front, etc.) on the tape.

Measure the drawer fronts and the sides, top, and bottom of the chest and add about 6-8″ to the each of your dimensions (there will be some fraying of the edges of the fabric so you need this extra amount to allow for that – you can cut off excess later if needed). Cut out pieces of fabric in those sizes. One tablecloth is enough fabric for all of the pieces that you’ll need to cover the chest as long as you lay it out in a way that you’re not wasting lots of fabric. Do not use the hemmed edges of the tablecloth – cut off and discard those.

Next step? Iron. Steam iron the heck out of your fabric to get out the fold marks and wrinkles.

The last step before adhering the fabric to your pieces is to prep the drawer fronts. Each drawer front comes with two predrilled holes for the handles. Fill these two holes with wood filler, wax, or putty. I used a Minwax pencil:

Then figure out where you want your new pulls and drill the holes for them. It helps to use painter’s tape to mark the spot that you’re drilling the holes and to keep the laminate of the wood from flaking off the surface when you drill them.

Want to save this post?

We'll email this post to you, so you can come back to it later!

You’re now ready to put your fabric on the fronts of your pieces. I originally tried Mod Podge but I quickly saw that it soaked through portions of the fabric and darkened its color so for plan B I used {this Super 77 Adhesive Spray}, which worked great. This stuff is SUPER sticky and a little goes a long way. You need to use it in a well ventilated area so I spread a big dropcloth out in the garage (with the garage door open) and did it there. The process is pretty simple. For each piece, spray a light coat of adhesive spray on the side of the piece that will be on the outside of the chest and then gently lay your fabric piece on top of it. Readjust the piece to align it properly by lifting it up and placing it back down as needed. Once your fabric piece is centered on the wood piece, press it down onto the wood piece and smooth out any wrinkles.

Now you need to wrap the fabric around the edges. Instead of trying to spray the edges, I found it was easiest to spray some of the adhesive spray on a paper plate and then use a small paintbrush to spread it on the edges. Doing it this way also keeps you from getting too much glue on the fabric. The glue on the plate and the wood piece dries very fast, so you have to keep spraying more on the plate and keep wrapping and pressing the fabric down on the edges as you go.

Beware that the two side pieces have holes on the edges. You need to notch out the fabric in those areas before adhering the fabric to the edges:

Once the fabric is adhered to all four edges of the wood piece, lay the piece on the ground with the fabric side down and fold the fabric edges over onto the back of the piece. Before adhering the fabric to the back, trim the fabric in any places necessary so that it will not end up covering any holes but that it is as close as possible to the holes. This step is important! If you cover up any of the holes with fabric, you are not going to be able to assemble your chest correctly. Once you’ve made any necessary cuts, use the same technique as you used with the edges to adhere the fabric to the back side of the wood pieces.

I used {this method} to do the corners, including cutting away extra fabric. I didn’t use any staples though – just the adhesive spray on a paintbrush. Once each corner is glued, it will need to be held down tight to the wood piece for several minutes until the glue dries. Your finished corners will end up looking like this:

After you’re done adhering the fabric to the front, edges, and back of the piece, it won’t look too pretty from the back:

No worries, it doesn’t have to be pretty – you won’t be able to see these ratty edges once the chest is assembled. Once you’re done adhering the fabric to all of your wood pieces, brush some Mod Podge around the edges on the backs of the pieces to keep the fabric in place and keep the edges from fraying further:

After everything dries it’s time to get our your IKEA instructions and start assembling! Once the chest is assembled, you’ll need to put your new pulls on. I chose {these ring pulls}:

To attach them to the drawer front, I put a skewer through each hole that I’d predrilled and moved the skewer from side to side to widen the hole a bit.

Then insert the screw for your pull through the hole in the drawer and through the opening in the fabric that you made with the skewer. Turn the pull (NOT the screw) to tighten it onto the drawer front. Turning the screw can pull at the fabric and create a run in it (yep, unfortunately I learned that the hard way…).

I wanted the legs of the chest to match my hardware so before attaching them to the chest, I sprayed them with {this Rustoleum Paint & Primer}:

Done!

I may end up getting a piece of glass cut for the top of the chest to protect it from getting dirty since I’m keeping a plant on it. I would definitely recommend a glass top if it will be a heavily used piece.

So what do you think? If you have any questions, shoot me an email or leave a comment. Enjoy the weekend!

IKEA Hack: Fabric Covered Chest

Want to save this post?

✉️FREE EMAIL SERIES ✉️

5 Secrets to Reinventing Your Home on a Budget

Leave a Reply Cancel reply

Want to save this post?

✉️FREE EMAIL SERIES ✉️

5 Secrets to Reinventing Your Home on a Budget

Reader Interactions

Comments

Leave a Reply Cancel reply